Trusted hvac installation for Columbus properties. Same-day service available, transparent pricing, and a workmanship guarantee.
A complete HVAC installation from KIC Refrigeration in Columbus, WI addresses every element in the comfort chain, from the air handler and condensing unit to the thermostat, ductwork, and filtration system. We ensure proper airflow balance, verified refrigerant charge, tested safety controls, and code-compliant operation before turning the system over to you.
Properties throughout Columbus (pop. 5,378) face unique demands when it comes to hvac installation. Wisconsin heating loads, cooling calculations, and the insulation levels and duct configurations found in Columbus homes all influence the approach we take. KIC Refrigeration tailors every hvac installation project to the conditions your property actually faces — no generic solutions.
Choosing the right contractor for hvac installation in Columbus, WI makes all the difference between efficient comfort and a system that short-cycles. KIC Refrigeration uses Manual J load calculations, installs to manufacturer specifications, and backs every project with a warranty. Call (866) 858-2961 to schedule your free assessment.
From initial contact to final verification — here is how we handle hvac installation.
We survey your property, assess your existing HVAC infrastructure, and perform a Manual J load calculation to determine the correct system size. We evaluate ductwork condition, electrical capacity, and equipment location options.
Our Columbus team presents two to three system options matched to your load calculation. We compare SEER2 and AFUE ratings, explain the differences between single-stage, two-stage, and variable-speed equipment, and factor in available manufacturer rebates, utility incentives, and federal tax credits for Columbus homeowners.
KIC Refrigeration installs HVAC systems in Columbus, WI to the highest standards. We set equipment on level, vibration-isolated mounting, braze all refrigerant connections with nitrogen flowing, pressure test with dry nitrogen, evacuate to below 500 microns, charge by weight, seal all duct connections with mastic, and verify gas piping sizing and connections.
We start the new system, verify operation in all modes, measure airflow, check refrigerant charge, program the thermostat, register the warranty, and provide you with all documentation including equipment manuals, warranty cards, and commissioning readings.
Get answers to the hvac installation questions our customers ask most often.
Complete HVAC installation in Columbus ranges from $7,000 to $15,000 for a mid-efficiency furnace and AC combination — typically an 80 percent AFUE furnace paired with a 14.3 to 16 SEER2 condenser. High-efficiency systems with variable-speed blowers and two-stage or variable-speed compressors run $12,000 to $22,000 but deliver significantly lower operating costs and qualify for federal tax credits. Heat pump systems fall between $5,000 and $18,000 depending on whether the system is single-stage, variable-speed, or a dual-fuel configuration. Ductwork modifications or new duct runs add $1,000 to $5,000. KIC Refrigeration provides detailed written proposals for Columbus homeowners with every cost itemized and no hidden fees.
Correct HVAC system sizing is determined by a Manual J residential load calculation — the ACCA industry standard — that accounts for your home square footage, ceiling height, insulation R-values, window area and U-factor, air infiltration rate, duct losses, occupancy, and the local WI winter and summer design temperatures. As a rough reference, a well-insulated 2,000-square-foot home in Columbus typically needs a 2.5 to 3.5 ton system, while a poorly insulated home of the same size may need 4 tons. KIC Refrigeration never estimates by rule of thumb — we run a proper calculation for your specific Columbus home to avoid oversizing, which causes short cycling, high humidity, and premature compressor wear.
A standard furnace and AC replacement in Columbus takes 1 to 2 days when existing ductwork, gas piping, and electrical service are adequate and the new equipment fits in the same location. A complete system replacement that includes ductwork modifications, new trunk lines, equipment relocation from basement to attic or vice versa, electrical panel upgrades, or zoning system installation may take 3 to 5 days. Multi-zone mini-split installations with 3 to 5 indoor heads typically take 2 to 3 days. KIC Refrigeration provides a clear timeline in every proposal, coordinates scheduling around your Columbus home availability, and keeps you informed on progress every step of the way.
Yes. KIC Refrigeration pulls all required mechanical, electrical, and gas permits for every HVAC installation in Columbus, WI. We prepare the permit application with equipment specifications and installation plans, pay the permit fee, schedule the inspection with the local building department, meet the inspector on-site, and ensure the installation passes all applicable mechanical code requirements. A building permit is not optional — it is required by law in most Columbus jurisdictions, and an unpermitted installation can void the manufacturer equipment warranty, create title problems when selling the home, and may not be covered by homeowner insurance if an HVAC failure causes property damage. KIC Refrigeration includes permitting in every installation project.
Hear from property owners who chose us for their heating and cooling needs.
"Called for an emergency AC repair on a Friday evening fully expecting to wait until Monday. They came out that same night. Cannot say enough good things."
"Heat pump was not heating properly. They found a bad reversing valve and had it swapped out the next day. House is warm again and the system runs great."
"AC tune-up went well. Found a refrigerant issue I did not know about and topped it off. Fair pricing and honest work."